{"id":208,"date":"2018-05-08T18:06:40","date_gmt":"2018-05-08T18:06:40","guid":{"rendered":"https:\/\/www.marix.com.br\/?page_id=208"},"modified":"2025-03-04T01:06:11","modified_gmt":"2025-03-04T01:06:11","slug":"wooden-pivot-doors-hinge-instalation-guide","status":"publish","type":"page","link":"https:\/\/marix.us\/index.php\/wooden-pivot-doors-hinge-instalation-guide\/","title":{"rendered":"Wooden Pivot Doors Hinge Instalation guide"},"content":{"rendered":"\n

Tools:<\/h2>\n\n\n\n
\n

<\/p>\n\n\n\n

A – SCREWDRIVER<\/strong><\/p>\n\n\n\n

B – LOWER HARDWARE<\/strong><\/p>\n\n\n\n

C – SCREW<\/strong><\/p>\n\n\n\n

D – 1-1\/2″<\/strong> DIAMOND CUP SAW<\/strong> (40mm)<\/strong><\/p>\n\n\n\n

E – MARIX SPRING WITH LID<\/strong><\/p>\n\n\n\n

Fl – TOP HARDWARE 1<\/strong><\/p>\n\n\n\n

F2 – TOP HARDWARE 2<\/strong><\/p>\n\n\n\n

G – 5\/16″<\/strong> VIDEO DRILL (8mm<\/strong><\/strong>)<\/strong><\/p>\n\n\n\n

H – 5\/16″<\/strong> BUSHING<\/strong> (8mm<\/strong><\/strong>)<\/p>\n<\/div><\/div>\n\n\n\n

\n
\"\"
Step 01<\/strong>
Place the hardware on top of the headboard. Ideal minimum suggestion of distance from the side of the span to thecenter of the hardware axis 60mm, as shown in the photo. Then make the recess to embed the hardware in the lining.<\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n<\/div><\/div>\n\n\n\n
\n
\"\"
Step 02<\/strong>
Complete the assembly of the lining and place it in the doorway.<\/strong><\/figcaption><\/figure>\n<\/div><\/div><\/div>\n\n\n\n
<\/div>\n\n\n\n
\n
\"\"
Step 03<\/strong>
Measure the width of the door;<\/strong>
The ideal clearance at the height of 12mm;<\/strong>
The ideal gap in the 8mm width.<\/strong><\/figcaption><\/figure>\n<\/div><\/div><\/div>\n\n\n\n
<\/div>\n\n\n
\n
\"\"
Step 04<\/strong>
Using the 1-1\/2″<\/strong> diameter diamond hole saw drill, drill a hole 70mm deep. Ideally suggested distance from the side of the span to the spring axis is 60mm. Attention: use water during all drilling.<\/span><\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n\n

<\/p>\n\n\n

\n
\"\"
Step 05<\/strong>
With the hole ready and cleaned to a depth of 70mm, check that the spring is completely free on the side and bottom.<\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n\n

<\/span><\/p>\n\n\n\n

<\/p>\n\n\n\n

<\/p>\n\n\n

\n
\"\"
Step 06.1<\/strong>
Fixing the upper hardware to the door:<\/strong>
Top: measure 57mm from the side of the door to the center of the hole, as shown in the photo, make a recess and screw the hardware into it.<\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n\n

<\/p>\n\n\n

\n
\"\"
Step 06.2<\/strong>
Fixing the lower hardware to the door:<\/strong>
Bottom: measure 57mm from the side of the door to the center of the square of the hardware, as shown in the photo, make a recess and screw the hardware onto it.<\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n\n

<\/span><\/p>\n\n\n

\n
\"\"
Step 07<\/strong>
Fit the door at a slight angle to the Marix spring, in the closed position, and then open the door by forcing the spring open until the screws of the upper bracket are accessible. Secure screws to top bracket.<\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n
\n
\"\"
Step 08<\/strong>
Then, with the door in the closed position, fix two screws on the spring diagonally. Attention: it is essential that the door is in the closed position and that at least 2 screws are fixed diagonally as shown in the photo.<\/span><\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n\n

<\/p>\n\n\n

\n
\"\"
Step 09<\/strong>
Make the door work by adjusting its ideal alignment using the two screws. Attention: This maneuver is necessary due to the internal spring mechanism and so that the alignment of the door with the lock is well adjusted.<\/span><\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n
\n
\"\"
Step 10.1<\/strong>
Slightly open the door, freeing access to the screws on the top bracket, then loosening them to remove the door. Return the door to the closed position, and disengage the spring door by removing it.<\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n\n

<\/p>\n\n\n

\n
\"\"
Step 10.2<\/strong>
Install the remaining two screws holding tight. Attention: make sure that the four screws are securely fastened to prevent the spring from moving, thus preventing the door from misaligning the lock.<\/span><\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n\n

<\/p>\n\n\n

\n
\"\"
Step 11<\/strong>
Place the cap over the Marix spring, pressing it until it snaps into place.<\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n
<\/div>\n\n\n\n

<\/p>\n\n\n

\n
\"\"
Step 12<\/strong>
Return the door to the closed position on the Marix spring. Open the door slightly by forcing the spring open to gain access to the upper bracket fixing screws. Reinstall screws on top hardware.<\/strong><\/figcaption><\/figure>\n<\/div>\n\n\n

<\/p>\n\n\n\n

Your Marix door closer is installed.<\/strong><\/p>\n\n\n

<\/div>
Guia de Instala\u00e7\u00e3o da Mola Marix em Portas Pivotantes de Madeira #vaivem #acoinox #moladepavimento<\/div><\/div>
<\/div>
<\/div>
<\/div><\/div><\/div>